Jerith Construction Service Nationwide | Barrett & Sons Construction

Why Los Angeles Homeowners Choose Jerith Construction

We provide independent Jerith aluminum fence, gate, and railing repair and installation across Los Angeles, from coastal neighborhoods dealing with salt air to hillside lots where slopes complicate every post hole. For homeowners looking specifically for Jerith repair in Los Angeles, our crews have the local experience to handle it. Our crews have installed and repaired hundreds of Jerith ornamental aluminum fences, and we know these products well enough to tell you honestly when a repair makes sense and when a section needs replacing. We’re not authorized by Jerith and we don’t claim to be, but as an independent Jerith service provider we carry genuine Jerith parts and the field experience to install them right the first time. If your Jerith gate is sagging or your powder coat is chalked from years of LA sun, call Barrett & Sons Construction at (877) 610-1318 for an honest assessment.

Call (877) 610-1318

Why Trust Barrett & Sons Construction for Your Jerith Construction?

Tom Barrett grew up in the San Fernando Valley, not far from the old stretch of Van Nuys Boulevard where his dad used to take him to watch crews pour foundations on weekends. He learned the trade at Los Angeles Trade-Technical College, starting with framing and finishing with enough hours in the field to know that the job never lies. That background matters when we’re working on your Jerith fence because post footings, gate geometry, and aluminum panel alignment all demand more precision than they look like they do.

Our crews have worked on Jerith Residential (RA series), Industrial (IA series), Ornamental (OA series), and Premier (PA series) fences across Los Angeles. We know how Jerith panels sit in their brackets, how their self-closing hinges wear, and where their powder coat tends to fail first in this climate. We keep genuine Jerith hinges, latch assemblies, and post caps on hand when available. When a part isn’t available, we’ll tell you before we substitute anything. Every job gets a written scope, every price change arrives as a written change order, and every completed fence or gate is backed by our 90-Day Done Right Promise: if it’s not done right, Tom comes back and makes it right, one call. We’ll do it right the first time, or we’ll come back and make it right.

Common Jerith Construction Problems We Fix in Los Angeles

Los Angeles is a rough place for any exterior metal product. Between the UV, the salt, the clay soil, and the occasional downhill creep of a hillside lot, Jerith fences and gates develop problems here that you simply won’t see in most other parts of the country. These are the five we see most often:

• Powder coat chalking and fading on dark finishes. Jerith’s black and dark bronze powder coat finishes look sharp when they’re new, but prolonged Los Angeles sun breaks down the resin binder over time. The surface turns chalky and dull, especially on south-facing and west-facing runs in neighborhoods like Tarzana and Woodland Hills. This is cosmetic at first, but once the coating starts lifting at panel edges and post seams, bare aluminum is exposed and corrosion begins. We touch up small areas with color-matched powder coat repair; for widespread failure, we’ll give you an honest cost comparison between recoating and replacing affected sections.
• Gate sagging from worn or sheared self-closing hinge bolts. Jerith gates use spring-loaded self-closing hinges, and over years of daily use those hinge bolts fatigue. Our tech responded to a Los Feliz home where a Jerith Premier aluminum gate had sagged so badly it scraped the concrete walkway. We found two of three self-closing hinge bolts sheared and the bottom hinge bracket corroded from irrigation overspray. We replaced the hinge bolts with Jerith OEM parts, installed a new stainless steel bracket, and re-hung the gate with a slight upward pitch, restoring smooth self-closing operation.
• Post leaning from expansive clay soil. Large parts of Los Angeles sit on expansive clay that swells when wet and shrinks when dry. That seasonal movement works against fence posts over the years, especially if the original footing was poured too shallow or without gravel drainage beneath it. We regularly dig out leaning Jerith posts, pour new footings at the correct depth for the soil conditions, and reset the post plumb before reattaching panels.
• Panel-to-post bracket corrosion in coastal areas. In neighborhoods like Playa del Rey and San Pedro, where salt air carries inland for miles, the aluminum panels themselves hold up well but the screws and brackets that connect panels to posts corrode faster. We replace corroded hardware with stainless steel equivalents and coat the connection points to slow future oxidation.
• Bottom rail clearance issues on sloped lots. Hillside properties throughout the Santa Monica Mountains and Hollywood Hills have sloping ground that creates uneven gaps at the bottom of aluminum fences. Jerith panels are rigid, so if the original installation didn’t step the panels or rack them correctly for the slope, you get gaps where pets escape or unfriendly critters wander in. We re-hang or modify panels to follow the grade properly while keeping the fence structurally sound.

Jerith Parts & Our Repair-vs-Replace Approach

We use genuine Jerith replacement parts whenever they’re available: gate hinges, latch assemblies, post caps, panel brackets, and self-closing spring mechanisms. Genuine parts maintain the fence’s original fit, finish, and pivot geometry, which matters more than people expect. An aftermarket hinge that’s 1/8 inch off changes how the gate hangs, and a latch that isn’t designed for Jerith gate rails leaves a gap that rattles in the wind.

When a Jerith part is discontinued or backordered for weeks, we’ll source or fabricate a commercial-grade aluminum equivalent and tell you that’s what we’re doing before we do it. We don’t quietly substitute. As for repair versus replace, we’re straightforward: powder coat damage limited to a few small areas is almost always repairable. If posts or panels have lost structural integrity, if multiple brackets have corroded through, or if a gate has sagged far enough to compromise the post, patching becomes throwing good money after bad. We’ll recommend replacing the affected section and give you a written line-item quote so you see exactly what that costs before any work starts. Call (877) 610-1318 if you want an honest read on your Jerith fence.

Our Jerith Service Process - Step by Step

1. 1
   Diagnosis in writing. We inspect your Jerith fence or gate, identify the specific failure or installation issue, and put the diagnosis in writing. You get a line-item estimate that tells you which parts will be repaired and which will be replaced, with Jerith OEM parts noted where they’ll be used. Scope in writing, allowances in writing, change orders in writing.
2. 2
   Repair or installation. We pull permits when the job requires them, which on hillside retaining wall tie-ins and some gate automation work they do. Our crew members are background-checked and they carry the Barrett & Sons name on their shirts and their work. For Jerith fence installation, we set posts in concrete at the depth Los Angeles soil conditions demand, with gravel drainage beneath the footing where expansive clay is a concern.
3. 3
   Testing and adjustment. Self-closing gates get tested for closing speed, latch alignment, and hinge tension. Panel sections get checked for racking, post plumb, and bracket torque. We roll a level across the top line and adjust anything that’s off. On sloped lots, we check bottom clearance along the full run.
4. 4
   Warranty paperwork. Every job ends with our written 90-Day Done Right Promise. If something’s not right within 90 days, one call brings Tom back. We don’t bury that promise in fine print; it’s on the contract you sign before we start.

Jerith Products We Service & Install in Los Angeles

We service all four Jerith series: the Residential Aluminum Fence (RA series) used on most single-family homes, the Industrial Aluminum Fence (IA series) common around commercial properties and apartment buildings, the Ornamental Aluminum Fence (OA series) with its decorative picket styles, and the Premier Aluminum Fence (PA series), which has the heaviest gauge and sturdiest gate hardware of the bunch. We stock common Jerith gate hinges, latch assemblies, and post caps in our Los Angeles inventory for fast turnaround on repairs, including Jerith service in Glendale and surrounding communities. Panel sections and gates are ordered to spec, which usually means a few days to a couple of weeks depending on the finish color and height. We install new Jerith aluminum fencing, repair existing runs, rebuild leaning posts, adjust and re-hang gates, and convert manual gates to automatic openers with compatible hardware.

We Also Service These Brands

Jerith is a brand we know well, but it’s not the only fencing and exterior product we stand behind. Across our Los Angeles projects we also install and repair KraftMaid cabinets, Cambria and Silestone countertops, and Kohler fixtures in kitchen and bathroom remodels. If your property needs more than a fence repair, we can handle it.

FAQs - Jerith Construction Service in Los Angeles

Book Your Jerith Service in Los Angeles, CA

If your Jerith fence or gate is sagging, chalked, leaning, or just not closing the way it used to, call Barrett & Sons Construction at (877) 610-1318. We’ll inspect it, tell you what’s wrong in plain English, and hand you a written quote. Free estimates in Los Angeles.

Written by Tom Barrett, Owner at Barrett & Sons Construction, serving Los Angeles since 1998.