Roofing in Broadview Park - Written Price, Workmanship Warranty

Fast, Reliable Roofing Across Broadview Park

Roof replacement in Broadview Park runs $8,000 to $20,000 for a standard CBS ranch, and a coastal-spec job with stainless fasteners and sealed drip edge lands between $11,000 and $20,000. Most roof repairs here fall between $400 and $1,800 depending on whether we’re re-fastening eave edges or replacing rusted flashing. If you’re calling from SW 40th Avenue, 42nd Street, or anywhere in the 33317 ZIP, we’ll come out, look at the roof, and give you a line-item written estimate before you spend a dime. Call (877) 610-1318 and a live person answers.

Call (877) 610-1318

We know Broadview Park because we work here every week. The homes are mostly mid-century CBS ranches built between 1955 and 1975, and they share one thing in common: the original roofing hardware was never meant to survive decades of salt air coming off the Atlantic. That’s why we specify stainless and hot-dip galvanized fasteners on every job here. Cheaper inland-spec parts fail in eight to twelve years. We’d rather do it once.

Why Barrett & Sons Construction Is Broadview Park’s Preferred Roofing Company

Tom Barrett started this company in 1998, and his sons run crews across Broward County today. When you call about your Broadview Park roof, you’re not getting a call center in another state. You’re getting someone who’s pulled county permits at the Broward County Building Department, waited on inspections, and knows exactly which code official’s jurisdiction covers your street. That matters, because Broadview Park is unincorporated. Every permit, inspection, and certificate of occupancy runs through the county, not a city hall. We’ve done enough of them to know the timelines, the inspector pools, and the common reasons a final inspection gets delayed. We’d rather tell you that on day one than let you find out in week six.

Our customers in Broadview Park tend to be homeowners between 50 and 70 who’ve been burned by a national outfit before. They tell us the same story: a quote over the phone that changed at the door. We don’t work that way. Every estimate is written, every change in scope comes as a written change order before the work starts, and every job carries the 90-Day Done Right Promise in writing. You’ll also find Tom Barrett’s name, address, and license number published where you can verify it. Ask anyone on your street, or look it up yourself.

Response time to Broadview Park is same-week for estimates, and we answer the phone 24/7. Not a voicemail box, not a national dispatch line. A person. If something’s wrong after the job, one call brings Tom back. He lives twenty minutes away; if it’s not right, he wants to know.

Our Roofing Services in Broadview Park

Roof Repair

Roof repair in Broadview Park typically runs $400 to $1,800. The most common pattern we see is galvanized ring-shank nails sheared off at the thread line within two inches of the eave, especially on homes near the South New River Canal where salt-laden air moves on the prevailing east wind. We re-fasten the affected edges, replace rusted flashing, and seal the drip edge before it pulls water into the fascia. On partial re-roofs, we never reuse old galvanized fasteners. The salt already ate the zinc coating; putting the same nails back just schedules the next repair.

Roof Replacement & Installation

Full roof replacement in Broadview Park runs $8,000 to $20,000, but if you want the coastal spec, it’s $11,000 to $20,000. That means 316 stainless fasteners, hot-dip galvanized hardware on any exposed trim, and a sealed drip edge. The cheap inland-spec version uses standard electro-galvanized nails and unsealed edges. It passes inspection today. It starts failing in eight to twelve years. County code under the post-Andrew wind-load standards is strict, but code is a floor, not a ceiling. We re-roof to the coastal condition, not to the day of the permit.

Metal Roofing

Standing seam metal roof installation in Broadview Park runs $18,000 to $40,000 with marine-grade trim. We favor standing seam over exposed-fastener corrugated panels for one reason: the panel fasteners on exposed systems sit in the direct salt spray path. They corrode, the rubber washers crack, and water finds the hole. Standing seam hides the fasteners under the seam, and we specify marine-grade stainless clip hardware. For a 1960s CBS ranch, this is the closest thing to a permanent roof.

Tile Roofing

Tile roof repair in Broadview Park runs $600 to $2,500, and it’s usually a cracked barrel tile or a rusted nail-through-tile at the eave. Tile itself handles salt air better than asphalt shingle, but the underlayment and the fasteners under the tile still rot. When we repair tile, we replace the underlayment in the affected zone and use the same stainless hardware we’d put on a standing seam roof. It costs a little more than resurfacing the surface and ignoring what’s underneath, and that’s the point.

For any of this work, the Roofing team handles everything from the permit to the final inspection.

Trusted Brands We Service in Broadview Park

We install GAF asphalt shingle systems and certain specialty underlayments specified for coastal Broward County conditions, and we stock the common GAF colors most Broadview Park homeowners choose for their low-slope CBS ranches. Keeping local stock means we don’t wait on a distributor in another county when you need a few bundles matched or replacement ridge caps after a storm. We also work with standing seam metal panels from domestic mills, ordered to your roof’s exact profile and panel length. When a Broadview Park customer asks what brand we recommend, the answer is the one with a published technical spec for salt-air exposure, not whatever’s cheapest in the warehouse.

Common Roofing Problems We See in Broadview Park Homes

• Salt-air fastener failure. Galvanized roofing nails corrode within eight to twelve years near the South New River Canal corridor. The threads shear off at the eave, and shingles lift on the prevailing east side of the home. The fix is stainless re-fastening and edge sealing, not another layer over dead fasteners.
• Rusted eave flashing. The original 26-gauge zinc-coated steel flashing on mid-century ranches rusts through at the drip edge before the granule loss on the shingle becomes visible. We replace it with a thicker gauge and seal the transition to the stucco.
• Cracked low-slope built-up roofs. Homes from the 1960s often have low-slope built-up roofs that crack at scupper drains where the unsealed metal edge meets the stucco. June through September downpours drive water behind the fascia, into the soffit, and down the block wall.
• Wind-lift at the roof perimeter. Many original CBS ranches predate Florida’s post-Andrew wind-load mandates. Roof-to-wall straps either weren’t installed or are missing on part of the perimeter. We add strap points whenever we re-deck or replace sheathing along the eave.

On a 1963 CBS ranch off SW 40th Avenue, our crew pulled back the original low-slope cap sheet to find every galvanized ring-shank had sheared at the thread line within two inches of the eave, classic salt-air chloride pitting. We re-decked the affected zone, replaced all fasteners with 316 stainless, and added two new roof-to-wall strap points before closing the county inspection sign-off.

Pricing for Roofing in Broadview Park, FL

We Also Serve Cities Near Broadview Park

Our crews work Broadview Park, Roofing in Broadview Park being our focus for this area, and we also cover Plantation, Fort Lauderdale, Lauderhill, and Lauderdale Lakes. Same written estimates, same stainless-fastener coastal spec, same county permit process where it applies. If you’re a block over the line in Plantation, the roof still needs what the salt air demands.

FAQs - Roofing in Broadview Park