Schluter Roofing Nationwide | Barrett & Sons Construction

Schluter Roofing: The Los Angeles Owner’s Guide

We stock Schluter-compatible roofing components and install them across Los Angeles, with most replacements running $470 to $2,125 depending on the part and roof access. If you’ve got a Schluter system that’s leaking, cracking, or pulling away from the flashing, we can usually match the part same day and get it swapped within a few days. Most owners discover a failure the hard way: a water stain on the ceiling after a rain, or granules collecting in the gutter, or a soft spot underfoot near a penetration. By then the part has usually been failing quietly for months.

Call (877) 610-1318

Barrett & Sons Construction is an independent roofing and remodeling contractor. We’re not affiliated with Schluter, but we’ve been installing and repairing their roofing accessories in Los Angeles long enough to know which parts fail, which ones hold up, and what actually needs replacing versus what can be saved.

Which Schluter Models This Applies To

Schluter’s roofing line in the U.S. centers on their KERDI and DITRA waterproofing membranes plus their drainage and edge profiles, but the brand is better known on the tile side than on the roof itself. Where we see Schluter in Los Angeles roofing, it’s typically as a flashing or transition detail around parapets, dormers, and roof-to-wall intersections where a membrane meets a metal edge. If your roof has Schluter components, they’ll usually be labeled on the exposed flange or stamped into the metal edge itself.

The compatibility question matters more than most owners realize. Schluter profiles come in different heights and finish options, and a profile made for a 3/8-inch tile assembly won’t sit correctly against a 1/2-inch or 5/8-inch substrate. Measure the total depth from roof deck to finished surface, then check the stamped model number if the part is still legible. In our experience, OEM Schluter parts are worth the premium on anything that directs water, since aftermarket copies often use thinner gauge metal and skip the drainage channels that keep water moving. On purely cosmetic trim, a quality aftermarket equivalent saves money without compromising performance.

Signs Your Schluter Roofing Is Failing

• Water staining on ceilings below a dormer or parapet. Schluter flashing that’s separated from the roof membrane lets water travel sideways before it drops, so the stain may appear feet away from the actual failure point.
• Granules in the gutter concentrated near a roof-to-wall joint. Water funneling behind an edge profile erodes the shingle surface fast and the granules wash down first, which is an early signal the Schluter detail has opened up.
• Visible gaps or lifting at profile edges. Thermal movement in Los Angeles sun cycles from 40 degrees to 110 degrees works metal loose over time, and a profile that’s lifted a quarter inch is already letting water through.
• Rust or corrosion at fasteners. The original screws or nails holding a Schluter profile were often not matched to the metal, and once the fastener rusts, water follows the hole straight into the deck.
• Soft decking just inside a penetration or transition. By the time the deck feels spongy underfoot, water has been working there long enough to rot the substrate, which means the Schluter detail failed long before you noticed the surface issue.

Replacement Cost & What’s Included

For Los Angeles homeowners, replacing or re-flashing Schluter roofing components typically runs $470 to $2,125 installed, depending on how much profile needs to come out, roof pitch, and access. A single straight profile swap on a reachable dormer sits at the low end, while a full parapet re-flash with membrane repair and deck patching climbs toward the top. The breakdown we give you lists parts, labor, and disposal separately, so you see exactly what you’re paying for before the first shingle moves.

Every Schluter repair we do in Los Angeles carries the 90-Day Done Right Promise in writing. If something’s not right after we leave, one call brings Tom Barrett back to make it right. And if the scope changes mid-job, you’ll get a written change order with the new number on it before any additional work begins. No surprises at the end.

DIY or Call Us?

You can safely do two things yourself: identify the model number (look for the stamp on the flange or profile face), and take photos of the failure from the ground or a ladder if the roof is walkable. That helps us bring the right part on the first trip. What you shouldn’t do is peel back a Schluter flashing that’s failing, because once the membrane is separated from the profile, you’ve created a wide-open water path and you’re now on a clock. Roof work on a pitch with a water-damaged deck underneath is not a Saturday project. We’ve repaired more than a few DIY attempts where the owner made the leak worse before they called us. Do it right the first time, or we’ll come back and make it right. Call (877) 610-1318 and we’ll get you on the schedule.

FAQs