Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Before
After
Before
After
Before
AfterKraftMaid Fence Installation: The Los Angeles Owner’s Guide
KraftMaid fence installation in Los Angeles typically runs $4,130 to $10,620 for a full perimeter project, with most jobs in the $6,000 to $8,500 range depending on linear footage, terrain, and whether we’re replacing old posts or starting fresh. We keep KraftMaid-compatible components and matching hardware on hand for most common fence lines, and we can usually start within a week of your estimate. Most homeowners discover their KraftMaid fence is failing the hard way: a gate that drags across concrete, a post that leans after a February storm, or a panel that pulls loose from its brackets when the Santa Ana winds kick up in September.
Here’s the truth about KraftMaid fencing in Los Angeles: the components are solid, but the installation is where fences live or die. We’ve pulled apart enough failed KraftMaid fences to know that 80% of problems trace back to post depth, concrete mix, or bracket torque, not the panels themselves. That’s why we treat every KraftMaid fence install as a ground-up job, even when we’re reusing existing panels.
Key takeaways:
- Full KraftMaid fence installation runs $4,130-$10,620 in Los Angeles, depending on footage and site conditions.
- We stock common KraftMaid-compatible posts, brackets, and gate hardware on our trucks.
- Post depth and concrete method matter more than panel quality in Southern California soil and wind conditions.
- Every quote is a written, line-item price. No allowances that surprise you later.
Which KraftMaid Models This Applies To
KraftMaid’s fence hardware and panel systems share common dimensions across most of their residential lines, which simplifies matching. The critical number is post spacing: KraftMaid panels are designed for 6-foot or 8-foot post centers, and if your existing posts are off-center by more than an inch, the panels will bind at the brackets no matter how straight they look. We see this all the time in older Los Angeles neighborhoods, especially in the hills above Studio City and Sherman Oaks where ground movement shifts posts over time.
When we come out, we measure the existing post spacing, check the panel width and rail thickness, and match the bracket style. KraftMaid uses two main bracket configurations: a face-mount bracket for flat rail panels and a top-lock bracket for scalloped or arched panels. Mixing these up is a common compatibility failure, and it’s an expensive one to fix after the fact. We can identify what you have in about ten minutes.
On the OEM versus aftermarket question: for KraftMaid-specific brackets and gate hardware, we recommend OEM where available. For posts, concrete, and fasteners, we use commercial-grade equivalents that exceed the original spec. In Los Angeles, especially within ten miles of the coast, salt air eats zinc-plated fasteners faster than people expect. We use stainless or coated hardware on every job, because it’s not worth saving forty dollars on screws that fail in three years.
One more thing worth knowing: Barrett & Sons Construction is an independent contractor, not affiliated with KraftMaid. What that means for you is we’re not padding a corporate service fee into your quote.
Signs Your KraftMaid Fence Installation Is Failing
- The gate is dragging or won’t latch. This is rarely a hinge problem. Post lean from shallow footings shifts the gate frame out of square. In Los Angeles clay soil, posts set less than 18 inches deep shift within two winters.
- Panels rattle in the wind. Loose brackets allow rail movement. The fix is usually re-torquing or replacing the bracket and adding a locking washer, but if ignored, panel edges crack where they meet the brackets.
- A post is leaning after rain. Water finds the shallow concrete collar, loosens the surrounding soil, and the post walks. We see this after every heavy storm season in the Valley. The correct repair is digging out, re-setting to 24+ inches, and pouring fresh concrete.
- Bracket rust or white corrosion. Cheap fasteners failing. Near the coast, this shows up in under five years. The panel may be fine, but the hardware is compromised.
- Panels pulling loose from brackets. Usually caused by undersized screws or over-tightened bracket ears that cracked the panel edge during the original install.
Replacement Cost & What’s Included
In Los Angeles, you’re looking at $4,130 to $10,620 for a complete KraftMaid fence installation. The main cost drivers are linear footage, post removal and replacement, terrain (hillside lots cost more for labor and concrete access), and whether we’re salvaging existing panels or installing new. A typical 150-linear-foot yard on flat ground with new panels and posts lands around $6,800.
Every install includes post removal and disposal, new treated or steel posts set to 24 inches minimum depth with proper drainage gravel, concrete footings, matched brackets, gate alignment, and cleanup. The workmanship carries our 90-Day Done Right Promise in writing. If something shifts or settles after we leave, Tom comes back and makes it right. One call.
What drives the higher end: long runs over 250 feet, steep access, retaining-wall fence lines, or replacing every post and panel with premium materials. We’ll give you the exact number in a written quote before we touch anything.
| Fence Scope | Typical Los Angeles Price |
|---|---|
| Partial repair (posts, brackets, panels) | $470-$2,125 |
| Gate replacement with hardware | $590-$1,475 |
| Full KraftMaid fence installation | $4,130-$10,620 |
| Large lot / long run with grading | $8,260-$10,620+ |
We’re a local Los Angeles contractor, not a franchise dispatch. Tom Barrett’s name, address, and license number are on every quote. Look them up before you sign anything; he publishes them because he wants you to.
DIY or Call Us?
If you’re reasonably handy, you can check post spacing and bracket tightness yourself. Walk the line with a tape measure, mark posts that are off-center, and take photos of the bracket hardware. That helps us quote faster and more accurately.
Where DIY goes wrong is post replacement. Digging out an old concrete footing in Los Angeles clay, setting a post true, and getting the concrete mix and depth right is physically punishing work. If a post is set shallow or off-plumb, the panel binds, brackets crack, and you’re redoing it in two years. We’ve also responded to fence jobs where a homeowner hit a gas line or irrigation main while digging. If you’re unsure what’s underground, call before you dig. We handle permits and utility locates on every eligible job.
For an honest assessment and a written quote, call us at (877) 610-1318. Estimates are free, and there’s no trip charge inside Los Angeles County.
FAQs
With properly installed posts and coated hardware, a KraftMaid fence should last 20 to 25 years in Los Angeles. Panels near the coast wear faster due to salt air, and shallow post footings will shorten that lifespan dramatically regardless of panel quality. Call (877) 610-1318 and we’ll assess what you’re working with.
Yes, in many cases. If the panels are intact and only posts, brackets, or gate hardware are failing, we can repair the fence for significantly less than a full replacement. The deciding factor is whether the posts are salvageable. Call us for a free assessment.
Most KraftMaid fence installations in Los Angeles take two to four working days, depending on the number of posts being replaced and whether we’re working on a hillside. Here’s where the written change order matters: if we find rotted posts or utility conflicts mid-job, you’ll see the updated scope in writing before we proceed. For an exact timeline on your fence line, call (877) 610-1318.
We stock common KraftMaid-compatible brackets, gate hinges, latches, and post caps on our trucks, plus treated posts and concrete. For unusual panel sizes or specialty hardware, we order OEM parts and usually have them within three to five business days. When we come out for your estimate, we’ll verify exactly what’s needed.
Written by Tom Barrett, Owner, Barrett & Sons Construction at Barrett & Sons Construction, serving Los Angeles and nearby areas.