Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Before
After
Before
After
Before
AfterJeld-Wen Kitchen Remodeling: The Los Angeles Owner’s Guide
Jeld-Wen kitchen remodeling in Los Angeles typically runs $16,520 to $53,100 for a full kitchen, depending on cabinet line, countertop material, and how much wall work your older LA home needs. We stock Jeld-Wen-compatible cabinet hardware, hinges, drawer slides, and trim pieces on our trucks, and most part swaps happen same day. The usual giveaway that something’s failed: a drawer that sticks on one side, a cabinet door that won’t sit flush no matter how many times you adjust it, or a hinge that creaks like an old gate every time you reach for a coffee mug.
Which Jeld-Wen Models This Applies To
Jeld-Wen built several cabinet and millwork lines over the years, and the compatibility question hinges on one thing: your hinge bore pattern. Older Jeld-Wen cabinets from the 1990s and early 2000s used a 35mm cup hole spaced 3 inches on center for the screw pattern. Newer Jeld-Wen stock cabinets moved to a 42mm cup with a tighter 45mm screw spread. If you grab the wrong hinge, the door mounts crooked and binds against the frame. Flip a hinge over: the cup diameter is stamped inside the metal. Take a photo, measure the cup, and we can tell you over the phone whether it’s a stock item or a special order. For kitchen remodels, we’re installing full Jeld-Wen-compatible cabinet systems alongside KraftMaid and Cambria, so if you’re replacing rather than repairing, you have real brand choices that don’t force you into mystery-box materials.
Signs Your Jeld-Wen Kitchen Remodeling Is Failing
- Drawer slides that catch mid-pull. The ball bearings inside the slide have worn flat on one side, usually from years of uneven loading. You’ll feel a hitch about two inches from closed, and it gets worse in LA’s dry heat when lubrication evaporates faster.
- Cabinet door sagging at the corner. The hinge’s spring tension is gone, or the mounting screws have stripped the particleboard. Each time the door sags, the edge rubs the frame and shaves off finish, so the damage compounds.
- Soft-close stops working on one door only. The damper piston inside that specific hinge has blown its seal. You’ll hear a faint click, then a slam. Intermittent at first, then every time.
- Visible delamination on cabinet edges near the sink or dishwasher. Humidity and steam break down the edge banding adhesive. In Los Angeles, even “dry” neighborhoods like the Valley get enough dishwasher steam to lift veneer within eight to ten years.
- Hinges that creak or pop when you open the door. The metal knuckle inside the hinge has worn oblong. Lubricating buys you two weeks. The pop you hear is metal jumping its own wear groove.
Replacement Cost & What’s Included
For a full Jeld-Wen kitchen remodel in Los Angeles, plan on $16,520 to $53,100. A small kitchen remodel with Jeld-Wen-compatible cabinets lands between $10,620 and $23,600. Cabinet installation alone runs $4,720 to $15,340, and countertop installation is $2,360 to $7,670 depending on whether you go laminate or stone. Every quote is in writing before we touch a single cabinet. Parts are priced separately from labor, so you see exactly what the hardware costs and exactly what the install costs. All our work carries the 90-Day Done Right Promise, which is on the contract in plain English. If a hinge fails or a drawer binds after install, call us and it’s handled.
Key Takeaways:
- Full Jeld-Wen kitchen remodel in LA: $16,520-$53,100.
- Most hardware swaps are same-day; full remodels run 2 to 6 weeks depending on scope.
- We stock common Jeld-Wen hinge sizes and drawer slides on the truck.
- Written change orders before any scope change. Always.
DIY or Call Us?
Cabinet hardware is not a high-tension danger zone like garage springs, so you can safely check the basics yourself. Measure your hinge cup diameter, count the screw holes, and look for a model stamp on the drawer slide. Where DIY goes wrong is buying a “universal” hinge online that doesn’t match the bore pattern, drilling new holes into a Jeld-Wen cabinet, and ending up with a door that hangs crooked and splintered particleboard. If the hinge cup is 35mm, most quality aftermarket Euro hinges will work. If it’s 42mm, that’s a Jeld-Wen-specific footprint and you’ll save yourself a headache by calling us at (877) 610-1318. We’ll match it the first time.
FAQs
Expect 15 to 25 years from Jeld-Wen cabinets in LA, with cabinet boxes outlasting hinges, drawer slides, and edge banding. The dry climate actually helps the wood frame stay stable, but decades of dishwasher steam takes out the adhesive and hardware long before the box fails. Call (877) 610-1318 if your cabinets are close to that age and starting to show edge wear.
A loose screw hole can be repaired with a threaded insert, but a worn-out hinge cup or a blown soft-close damper needs replacement. Once the internal spring or piston fails, no adjustment brings it back. We keep common Jeld-Wen hinge sizes stocked, so the swap usually happens in one visit.
Most hinge and drawer-slide replacements take 30 to 90 minutes once we’re on site. Full cabinet door re-hanging or edge banding replacement runs a half day to a full day. We’ll give you a time window in writing before we show up.
We stock the most common Jeld-Wen hinge sizes, drawer slides, and soft-close adapters on our trucks. Special-order hardware typically arrives in 3 to 5 business days, and we handle the ordering so you don’t end up with the wrong cup size. Call (877) 610-1318 with your hinge measurement and we’ll check the truck before you buy anything.
Ready to Fix It or Remodel It?
If you’re in Los Angeles and tired of a kitchen that fights you for every drawer, call Barrett & Sons Construction at (877) 610-1318. We’ll give you a free estimate in writing, match your Jeld-Wen hardware to what’s actually on the truck, and if it’s not done right the first time, we’ll come back and make it right. That’s the promise, and it’s on paper.
Written by Tom Barrett, Owner, Barrett & Sons Construction at Barrett & Sons Construction, serving Los Angeles and nearby areas.