Belgard Fence Installation Nationwide | Barrett & Sons Construction

Belgard Fence Installation: The Los Angeles Owner’s Guide

Belgard fence installation in Los Angeles typically runs $4,130 to $10,620 for a complete post-and-panel system, including material, concrete footings, and labor. We stock Belgard-compatible posts, panels, and hardware on our trucks, so in most cases we can match your existing product and schedule installation within a week. Owners usually find us after a gate post has started leaning, a panel cracked at the base, or a property line fence shifted after heavy rain, and they want it fixed without losing the matching Belgard look across the rest of the yard.

Call (877) 610-1318

We’re an independent fence contractor in Los Angeles, not a division of Belgard. That matters because we’ll tell you straight when a repair beats a replacement, and when the smarter money is swapping a section before the whole run goes. Tom Barrett started framing houses in the San Fernando Valley long before he hung his first Belgard panel, so we approach fence work the way a builder would: footings first, fasteners second, and never a visible seam where the gate swings.

Which Belgard Models This Applies To

Belgard’s fence and hardscape lines share the same modular rail system across several product families: the Metropolitan collection (clean, flat-top panels for modern Los Angeles yards), the Dublin collection (decorative scalloped or arched toppers), and the Weston collection (heavier, castle-wall profiles often used on hillside lots in Silver Lake and Echo Park). The compatibility gotcha we see all the time is this: Belgard changed its post width from a true 4″ square to a 4.25″ square on panels made after 2019. Order a replacement based on the panel name alone and you’ll fight the bracket for an hour before you realize the post is the problem.

To identify your part, flip any post cap and look for the mold stamp on the inside wall. It’ll show a two-letter series code and a four-digit date. Write those down before you call anyone. As for OEM versus aftermarket for Belgard fence sections: the factory panels are cast with a color-integral pigment that goes all the way through, so a chipped corner doesn’t show white. Most aftermarket panels are surface-coated. In Los Angeles sun, a surface coat fades unevenly within three years. For a fence you’ll look at for fifteen, we recommend OEM Belgard panels every time. You can see the difference where a west-facing fence has been baked by afternoon glare.

Signs Your Belgard Fence Installation Is Failing

• Gate post leaning more than an inch out of plumb. This usually means the original installer skimped on the concrete footing, or used dry-pack instead of wet concrete around the post. Once the base moves, the gate hardware binds and the panel joint at the top opens up.
• Hairline cracks running vertical through a panel, not along a seam. That’s thermal stress. In Los Angeles we get enough of a marine layer swing for panels to expand and contract, and a panel with no expansion gap at the post will eventually crack itself. It’s not a character mark. It’ll grow.
• Urethane joint seal separating from the post cap. Water gets behind it, then the freeze-thaw cycle in the foothill neighborhoods, like Tujunga or Sunland, works the cap loose. You’ll see the same failure on pool deck fences where sprinklers hit the base every morning.
• Rust streaks bleeding from any bracket or screw. That means someone used uncoated hardware. Belgard specifies stainless or powder-coated fasteners for a reason. The fix starts with replacing every fastener on the affected section, not painting over the rust.
• Panels rattling in the wind or shifting when you push on them. Loose mechanical connections, stripped screws, or a broken internal clip. A panel that moves is a panel that’ll fail under the first Santa Ana wind event of the season.

Replacement Cost & What’s Included

For Los Angeles homeowners, a Belgard fence installation or full section replacement lands between $4,130 and $10,620, depending on linear feet, gate size, and whether the existing footings can be reused. The lower end covers a partial run with one gate and clean access. The upper end covers a full perimeter fence with a wide double gate, deep footings, and sloping grade in the Hollywood Hills or Mount Washington.

• Panels and posts (OEM Belgard): roughly 55-65% of total job cost
• Concrete footings, hardware, brackets: roughly 15-20%
• Labor, haul-away, cleanup: roughly 20-25%

You get a written line-item quote before we start, and if the scope changes, you get a written change order before that work happens. The 90-Day Done Right Promise covers every Belgard fence installation we do in Los Angeles. If a post settles or a panel comes loose, one call brings us back.

DIY or Call Us?

There’s nothing on a Belgard fence panel that’ll hurt you the way a garage door spring will, but the labor is heavier than most people expect. A full 6′ Weston panel weighs close to 90 pounds, and setting a post correctly means digging below the root line, which in older Los Angeles neighborhoods means fighting compacted caliche and decades of sprinkler line additions. What an owner can safely check: panel codes, visible cracking, loose screws, gate alignment. What goes wrong with DIY: under-dug footings that sink after the first real rain, panels shimmed to hide an out-of-level post, and brackets torqued so hard the cast concrete spalls behind the screw.

If you want to try matching a single panel yourself, we’ll help you over the phone. But if you want the gate swinging square, the line straight, and the permit pulled where your city requires it, call us at (877) 610-1318 and we’ll come look at the whole run, take measurements, and put a scope in writing.

FAQs