Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Before
After
Before
After
Before
AfterBarrette Kitchen Remodeling: The Los Angeles Owner’s Guide
If you’ve got a Barrette kitchen component that’s failed or wearing out, a full Barrette kitchen remodeling project in Los Angeles typically runs $16,520 to $53,100 installed, depending on cabinet line, countertop material, and how much of the existing layout we’re reworking. We stock Barrette-compatible hardware, hinges, drawer slides, and trim on the truck, and we can usually match your existing doors or panels within a few business days. Most Los Angeles homeowners discover a problem the same way: a drawer that won’t close tight, a hinge that groans every morning, or a cabinet face that’s started to separate at the seam after a decade of inland heat and coastal humidity swings.
Which Barrette Models This Applies To
Barrette has produced several cabinet and hardware lines over the years, and the compatibility gotcha is that older series don’t always accept newer hinge plates without a retrofit plate. If your cabinets were installed before roughly 2010, the hinge cup spacing and door overlay may differ from current production. The fastest way to identify what you have: pull one hinge off and look for a stamped number on the back of the cup, then measure the door overlay to the sixteenth of an inch. Both numbers matter. For Barrette specifically, we generally recommend OEM hardware when the cabinet boxes are still square and you’re keeping the existing doors. OEM hinge geometry matches the factory drilling, which means the doors hang exactly where they did on day one. When the doors themselves are shot, quality aftermarket panels with the same overlay can save you fifteen to twenty percent over factory replacements, and we’ll tell you when that tradeoff makes sense. KraftMaid and Cambria are the other two kitchen brands we regularly match parts for, so if you’re not sure whether your current setup is Barrette or something else, bring us a photo and a hinge sample.
Signs Your Barrette Kitchen Remodeling Is Failing
- Drawers dragging or sticking in one spot. Usually a worn or bent slide, often the undermount style Barrette used on several mid-2000s lines. The nylon wheels flatten over time and the drawer starts grinding on the cabinet frame.
- Hinges that sag or doors that won’t line up square. The hinge spring loses tension after years of cycles, and adjusting the screws only buys you a few weeks. Once two adjacent doors start rubbing, the hinges are done.
- Loose or cracked cabinet faces at the corner joints. Los Angeles swings from dry Santa Ana weeks to humid coastal mornings, and engineered wood expands and contracts along the joint line. Hairline cracks at the corners are the first sign the face is separating from the frame.
- Soft-close mechanisms that slam. The damper inside a Barrette soft-close hinge or slide fails long before the metal wears out. If the door closes like a screen door now, the damper’s gone.
- Discolored or peeling trim and end panels. Sun exposure through south-facing Los Angeles windows breaks down the finish on exposed surfaces first. End panels and upper trim go chalky years before the main doors fade.
Replacement Cost & What’s Included
For a full Barrette kitchen remodeling job in Los Angeles, you’re looking at $16,520 to $53,100, and the spread mostly comes down to countertop material, cabinet count, and whether we’re moving plumbing or electrical. Cambria quartz countertops alone run $2,360 to $7,670 installed. Backsplash adds $945 to $2,950. Cabinet installation as a standalone line item runs $4,720 to $15,340. Every estimate we write is a written scope with line-item pricing, and if anything changes between the handshake and the final walkthrough, you get a written change order before work proceeds. The 90-Day Done Right Promise comes with every job in writing: if it’s not done right, one call brings Tom Barrett back to make it right. We don’t bury that in fine print, and we don’t hand you a different bill at the door.
DIY or Call Us?
Swapping a hinge or a drawer slide is something a patient homeowner can do with a screwdriver and the right replacement part, and we’ll happily sell you the hardware and tell you which screw holes to use. What we’d caution against: any repair that involves removing a cabinet face or realigning an entire run of doors. Once one face is off, getting the reveals even again takes a level, patience, and usually a second set of hands. That’s when a small job turns into a weekend that ends with a call to us anyway. If you’re not sure which situation you’re in, call (877) 610-1318 and describe what’s failing. We’ll tell you honestly whether it’s a twenty-minute fix or a job for our crew, and the second opinion is free.
Barrette Kitchen Remodeling in Los Angeles: FAQs
Barrette cabinet boxes and doors typically last 20 to 30 years in Los Angeles if they’re not exposed to direct sun, but hinges and slides are wear items and usually need replacement at the 10 to 15 year mark. Coastal humidity and inland temperature swings shorten the lifespan of finishes and adhesives compared to more stable climates. Give us a call at (877) 610-1318 and we’ll tell you whether your cabinets are worth repairing or past the point of chasing parts.
Damper failures and worn nylon wheels can’t be repaired, only replaced, and the cost of a new hinge or slide is usually less than the labor to nurse the old one along. When the damage is limited to hardware, replacement is the cheaper and cleaner fix. Call (877) 610-1318 for an exact price on parts and labor, and we’ll give you a written estimate before we start.
A full Barrette kitchen remodel in Los Angeles typically takes three to seven weeks depending on cabinet lead times, countertop fabrication, and whether we’re pulling permits for plumbing or electrical changes. A hardware-only replacement, like new hinges and slides throughout the kitchen, is usually done in a day or two. We’ll give you a written timeline as part of the estimate, and every change to that timeline arrives as a written change order first.
We carry common Barrette hinges, slides, dampers, and mounting plates on our trucks, and we can source OEM replacements for most older series within a few business days. If we don’t have it on hand, we’ll tell you exactly what to order or order it for you. Call (877) 610-1318 with your hinge sample or a photo, and we’ll match it before you spend a dollar.
Written by Tom Barrett, Owner, Barrett & Sons Construction at Barrett & Sons Construction, serving Los Angeles and nearby areas.