Andersen Construction in Fort Lauderdale, FL

Andersen Construction in Fort Lauderdale, CA | Barrett & Sons Construction

We provide independent Andersen window and door installation, repair, and replacement across Fort Lauderdale, from Victoria Park to the finger islands. What sets our Andersen work apart here is straightforward: we know how salt air, HVHZ wind codes, and aging canal-front concrete-block homes stress these units in ways a generic installer never sees coming. That knowledge changes what parts we order, how we flash the openings, and whether a repair will actually hold. Call Tom Barrett’s team at (877) 610-1318 for a free estimate on any Andersen project in Fort Lauderdale.

Why Fort Lauderdale Residents Choose Us for Andersen Service

Tom Barrett grew up in the San Fernando Valley, not far from the old stretch of Van Nuys Boulevard where his dad used to take him to watch crews pour foundations on weekends. He learned the trade at Los Angeles Trade-Technical College, then spent decades on job sites before starting Barrett & Sons in 1998. Now his sons run crews of their own, and Tom still shows up on most Fort Lauderdale jobs to check the work himself.

But familiarity with Andersen is only half of it. Our teams have worked on hundreds of Andersen window and door installations in Fort Lauderdale’s canal-front and concrete-block housing stock. We carry genuine Andersen replacement parts: sash locks, weatherstrip, operators, rollers, glass packs. We give honest repair-versus-replace advice because we’ve seen which failures come back and which ones don’t in this climate. If a frame is corroded or the seal is gone, we’ll tell you. If a repair makes sense, we’ll fix it and stand behind the work.

Common Andersen Construction Problems We Solve in Fort Lauderdale

• Salt-air corrosion on Andersen wood sashes. Canal-front homes in Coral Ridge and the finger islands get constant salt spray. The bottom rail of a 400 Series Woodwright sash is where the weatherstrip channel holds moisture against the finish. That’s where finish peels first, and where rot follows if nobody catches it early.
• Fogged insulated glass on 200 Series Perma-Shield units. We see fogging in roughly 15% of 1990s-era 200 Series units here, which lines up with what coastal inspectors report. High UV and daily humidity cycling strain the seals until the argon escapes and condensation builds inside the glass pack. Once that seal fails, the fix is replacement glass, not a repair.
• Sticking or dropping casement sashes on 400 Series units. Trade winds keep windows open for months at a time in Fort Lauderdale. The operator gears wear out from that constant use, especially on finger-island homes where there’s nothing to block the breeze. A sash that drops when you try to open it is almost always a worn operator, not a frame problem.
• Roller and track failure on Andersen gliding patio doors. Most of the concrete-block homes in Victoria Park and Tarpon River were built between the late 1940s and mid-1970s. Settlement has thrown doors out of square over the decades. Rollers bind, tracks wear unevenly, and doors jump or stick. We re-shim the frame, replace the rollers with genuine Andersen parts, and get the door sliding again.
• Leaky Andersen French doors after heavy rain. This is a frequent complaint during Fort Lauderdale’s summer storm season. The answer is rarely the door itself. More often, the flashing or sill pan underneath was never detailed correctly for HVHZ wind-driven rain, and the water finds the path of least resistance. We correct the rough opening, then reset the door.

Andersen Service in Fort Lauderdale: What Local Conditions Mean for Your Equipment

Here’s a fact about Fort Lauderdale that doesn’t apply to Pompano Beach or Hollywood the same way: this city has over 165 miles of navigable canals, which earned it the nickname “Venice of America.” That canal density means a disproportionate share of Andersen installations happen on finger-island lots where the home’s structural frame sits close to a seawall. And those seawalls move. On canal-front lots throughout Coral Ridge and the finger islands, contractors regularly find aging concrete seawalls that have rotated inward beneath existing pool decks and patio slabs, a failure driven by tidal soil saturation. When a seawall rotates, the surrounding soil settles, the slab shifts, and window and door openings fall out of square. Fort Lauderdale is one of the only cities in Florida where a standard Andersen window replacement on a pre-1970 canal-front home can trigger a Broward County seawall inspection if the existing seawall shows inward rotation. No neighboring city has the same concentration of finger-island lots where the seawall and the window framing are structurally interdependent. That’s why we check for frame squareness and wall deflection before quoting any Andersen replacement on a canal-front lot in Fort Lauderdale. Skip that step, and your new Andersen window gets installed into an opening that’s already moving.

Andersen Models & Products We Service in Fort Lauderdale

We work on the full Andersen lineup: the 400 Series Woodwright, the A-Series Architectural line, the 200 Series Perma-Shield, and the 100 Series Fibrex. For repairs, we source genuine Andersen replacement parts so the weathertight seals and color match stay factory-correct. Aftermarket parts might save a few dollars, but they don’t seat the same way, and in salt-laden air, a poor seal means corrosion starts early. For full unit replacements in Fort Lauderdale, we recommend impact-rated glass and stainless steel fasteners rated for coastal exposure whenever the home sits within a mile of salt water. On the parts side, we stock the common failure items locally so most Andersen repair calls in Fort Lauderdale don’t wait on a warehouse halfway across the state.

Andersen Service Pricing in Fort Lauderdale

FAQs - Andersen Construction in Fort Lauderdale

Do I need a permit to replace Andersen windows in Fort Lauderdale if the house was built before the HVHZ code took effect?

Yes, you need a permit for any window replacement in Fort Lauderdale, and the pre-HVHZ age of the house is exactly why. Most pre-1970 concrete-block homes in Victoria Park and Tarpon River lack modern hurricane strapping, impact-rated openings, and reinforced roof-to-wall connectors. When you pull a permit for a window swap, Broward County typically requires the new openings to meet current HVHZ design-pressure standards, which can mean upgrading the anchoring and flashing details, not just swapping the sash. We pull permits and get inspections signed on every eligible job. Call (877) 610-1318 for a free estimate, and we’ll explain exactly what your house will need.

Why do my Andersen French doors bind on a canal-front lot in Fort Lauderdale?

Binding on a canal-front lot in Fort Lauderdale is almost always structural, not a hardware problem. The soil under canal-front homes is saturated by tidal action, and the concrete seawalls along the property line can rotate inward over time. When that happens, the slab settles unevenly, and the door frame goes out of square. The door binds because the opening moved, not because the hinges wore out. We check for that deflection first, then tell you honestly whether the fix is a hardware adjustment or a more involved re-leveling of the opening.

Can you install Andersen 100 Series Fibrex windows in a Fort Lauderdale house that is within 1 mile of the ocean?

You can, provided the units carry the proper design-pressure rating for the home’s wind zone. Fort Lauderdale sits fully within Florida’s High-Velocity Hurricane Zone, which mandates 170+ mph design-pressure testing for windows and doors. Not every Fibrex unit meets that rating out of the box. For homes within a mile of salt water, we also recommend upgraded stainless hardware and proper corrosion-resistant flashing details, because the standard fasteners won’t hold up. We’ll specify the right unit and the right hardware for your exact address.

What is the difference between a standard Andersen window replacement and an impact window installation in Fort Lauderdale?

A standard Andersen replacement replaces the sash and frame with a new Andersen unit that meets the home’s existing wind requirements. An impact window installation is different: the entire unit, including the glass pack and frame, is tested and rated to withstand a 170+ mph design pressure and direct missile impact. In Fort Lauderdale, most permitted replacements in the HVHZ require impact-rated or otherwise code-compliant units, especially on the coast. The price difference is real, and so is the insurance savings. Call (877) 610-1318 and we’ll price both options for your home.

My Andersen sliding patio door is leaking during heavy rain. Is this a common problem in Fort Lauderdale?

Yes, and it’s usually not the door’s fault. Fort Lauderdale’s summer storms drive rain horizontally, and an Andersen gliding patio door installed without a properly detailed sill pan and flashing will leak in those conditions even if the door itself is perfectly weathertight. On older concrete-block homes, we often find the original opening was never flashed for HVHZ wind-driven rain at all. We correct the rough opening, reset the door, and re-caulk with a polyurethane sealant approved for coastal exposure. Call (877) 610-1318 for a free estimate and we’ll find where the water is actually getting in.

Service Areas Near Fort Lauderdale

We serve Fort Lauderdale and the surrounding cities, including Hollywood, Pompano Beach, Oakland Park, Wilton Manors, and Dania Beach. If you’re looking for Andersen service in West Palm Beach, our crews make that run regularly, and we also handle Andersen service in Hialeah for customers further south. You can learn more about our full Fort Lauderdale service area or browse our complete Andersen sales & service lineup.

Book Your Andersen Service in Fort Lauderdale Today

Our crew recently replaced three Andersen 400 Series casement windows on a 1962 concrete-block home in Coral Ridge just off the Intracoastal. The homeowner complained the sashes wouldn’t open past a few inches, and we found the aluminum operators had corroded from salt spray off the canal. We installed genuine Andersen replacement operators, re-shimmed the frames within the old stucco openings, and added stainless steel fasteners rated for coastal exposure, then re-caulked with a polyurethane sealant approved for the HVHZ. That’s the level of detail every Andersen job in Fort Lauderdale gets from us.

We’ll do it right the first time, or we’ll come back and make it right. Call (877) 610-1318 to schedule your free Andersen estimate in Fort Lauderdale today.

Written by Tom Barrett, Owner at Barrett & Sons Construction, serving Fort Lauderdale since 1998.