Andersen Fence Installation Nationwide | Barrett & Sons Construction

Andersen Fence Installation: The Los Angeles Owner’s Guide

Andersen fence installation in Los Angeles typically runs $4,130 to $10,620 for a complete vinyl privacy or semi-privacy fence, including materials, labor, and haul-away of your old fence. We stock Andersen fence panels, posts, gates, and hardware on our trucks and can usually match your existing Andersen line the same day we come out for the estimate. Most Los Angeles owners call us after a wind event or a vehicle bump leaves a post leaning, a gate dragging, or a panel cracked through – and they want the new section to match the old one without tearing the whole yard apart.

Call (877) 610-1318

We’re an independent Los Angeles fence installer, not an Andersen corporate entity. That matters because we’ll tell you straight what’s worth keeping and what’s shot, without a brand script to follow.

Key Takeaways

• Installed Andersen vinyl fence replacement: $4,130-$10,620 in Los Angeles, depending on linear feet, terrain, and gate count
• We stock Andersen-compatible panels, posts, gates, and hardware, plus quality aftermarket equivalents when they save you money
• Every job includes a written line-item quote before work starts – no surprises at the end
• Tom Barrett’s name, address, and license number are published and verifiable, and we pull permits on every eligible Los Angeles fence job
• 90-Day Done Right Promise written on every contract: if it’s not right, we come back and make it right

Which Andersen Models This Applies To

Andersen sells fence lines through a few product families, and in Los Angeles we see three most often: the Andersen 400 Series vinyl privacy fence (tongue-and-groove pickets, 6-foot panels), the Andersen Estate semi-privacy line (spaced pickets with a scalloped or straight top rail), and the Andersen Enclosure system for pool and perimeter runs that need code-compliant spacing. Each line uses different panel widths, post profiles, and rail-channel depths, and that’s where homeowners get tripped up.

Here’s the compatibility gotcha: an Andersen 400 Series panel will not seat properly in an Estate post, even though both are 6 feet tall and white. The rail channels are cut to different depths and the post routing doesn’t align. That’s the number-one mistake we see from handymen who grab “a vinyl fence panel” off a supply yard shelf. Before you buy anything, look for the series stamp on the inside of a post cap or the underside of a top rail. If it’s faded or gone, measure the rail channel depth – 400 Series runs 1-1/2 inches deep, Estate runs 1-1/4. We’ll verify it on-site during the free estimate.

On the OEM-versus-aftermarket question: for posts and gates, we recommend sticking with Andersen-brand or Andersen-licensed equivalents. For individual pickets and decorative post caps, quality aftermarket parts match fine and can cut material cost by 10 to 15 percent. We carry both so you’re not stuck with a brand markup on a part that doesn’t need it. And if you’re in a Los Angeles neighborhood with an HOA, we’ll confirm the replacement matches the approved color and profile before we order anything.

Signs Your Andersen Fence Installation Is Failing

• Post leaning at the base. In Los Angeles, this usually means the original post was set in concrete that’s cracked or the post wasn’t deep enough to begin with. Once water gets into the post sleeve, freeze-thaw isn’t the issue here – it’s soil shifting in the clay-heavy spots like the San Fernando Valley and parts of the Westside. A leaning post only gets worse, and it’ll pull the panels out of alignment next.
• Panels sagging or separating at the rail. Vinyl expands and contracts with heat, and Los Angeles summers test that daily. If the rail channel is worn or the factory notches have stretched, panels start to drop. You’ll see gaps at the top where two panels meet.
• Gate dragging or won’t latch. Most Andersen gate failures in Los Angeles come from the hinge post moving, not the hinge hardware itself. A metal hinge on a vinyl post puts all the stress on the post wall, and once the post flexes, the gate drops and the latch misses the strike plate.
• Pickets cracked or punctured. Lawn mowers, baseballs, and the occasional backed-in minivan take their toll. One cracked picket can often be swapped, but if the bottom rail is broken, the panel’s done – vinyl panels are welded at the factory, not assembled on-site.
• White vinyl turning chalky or stained. Andersen vinyl holds color well, but sprinkler water with high mineral content will leave deposits that dull the finish over a decade in the Los Angeles sun. That’s cosmetic, not structural – but it’s usually the moment owners start thinking about a full replacement anyway.

Replacement Cost & What’s Included

For Andersen fence installation in Los Angeles, most full-yard replacements land between $4,130 and $10,620. A single 6-foot panel replacement with one post runs $350 to $600 installed. A gate replacement with new posts and hardware runs $750 to $1,500 depending on width. A 100-linear-foot run with two gates typically falls in the $7,000 to $9,000 range when you factor in terrain and old fence haul-away.

What drives the price in Los Angeles: access (narrow side yards and hillside lots add labor), existing concrete removal, post depth requirements, gate count, and whether you’re matching an HOA-approved profile. Every quote we write is a line-item scope in writing, with allowances in writing. The labor number on your estimate is the labor number on your invoice – unless something changes, and then you get a written change order and you sign it before we pick up a tool. We’ve been doing it that way in Los Angeles since 1998.

Every Andersen fence job we install is backed by our 90-Day Done Right Promise. If something’s not right, one call brings Tom Barrett back out. Simple as that.

DIY or Call Us?

You can safely check the series stamp yourself, measure the panel height and width, and clear vegetation away from the base of the post. Digging out a leaning post and resetting it in new concrete is doable for a handy owner – but here’s where DIY goes sideways: matching the panel profile, getting the post plumb and the rails aligned without gaps, and most of all, setting posts deep enough for Los Angeles soil. Get a post 6 inches too shallow in clay soil and you’ll be leaning again in two years.

If the gate hardware involves high-tension hinges or a heavy double gate, let a pro take it. A vinyl gate swinging off a failed hinge can hurt someone. We’ll do it right the first time, or we’ll come back and make it right. If you’d rather spend your Saturday doing something else, call (877) 610-1318 and we’ll come out, match your Andersen line, and hand you a written price on the spot.

FAQs