Unilock Kitchen Remodeling Nationwide | Barrett & Sons Construction

Unilock Kitchen Remodeling: The Los Angeles Owner’s Guide

A Unilock kitchen remodel in Los Angeles typically runs $16,520 to $53,100 installed, and the range depends on what’s failing or outdated: countertop edges, pavers used as backsplash accent walls, or full layout reconfiguration. Most homeowners call us when they spot a cracked paver facing, a sink reveal that’s shifted, or grout lines that have gone from crisp to crumbling. We’ll match the existing Unilock product, price the fix or full remodel in writing, and handle the whole job, permits included.

Call (877) 610-1318

We’re an independent Los Angeles contractor, not a Unilock affiliate, but we’ve installed and remodeled with their product line for years and carry the common replacement pieces on our trucks. If you’ve got a Unilock kitchen feature that’s failing, this page tells you what it should cost, what actually has to be replaced, and when to stop looking at it and call us.

Key Takeaways

• Installed Unilock kitchen remodeling in Los Angeles: $16,520-$53,100, depending on scope and product match.
• Most failures we see are cracked paver faces, shifted sink reveals, and grout or joint failure, not structural problems.
• Matching the exact Unilock color batch matters more than most people expect before the first tile is pulled.
• We carry common Unilock-compatible pieces and order the rest direct; the swap is usually measured in days, not weeks.

Which Unilock Models This Applies To

Unilock’s kitchen applications in Los Angeles usually fall into two buckets: their paver and wall units used as backsplash accents, island facings, or feature walls, and their dimensional stone products used for countertop edges and trim. The product line you have changes what we match: U-Cara panels, Brussels Block pavers, or Lineo dimensional stone all take different setting materials and different joint compounds.

Here’s the gotcha most homeowners don’t know until it’s too late: Unilock runs color batches by production week, and a paver or panel bought in 2019 will not match a batch poured in 2025. That matters if you’re repairing one section of a backsplash or refacing one side of an island. We photograph the existing piece, check the stamped code on the back or bottom edge when it’s visible, and order against that batch number before we tear anything out. If the batch isn’t available, we’ll tell you before you spend a dollar, and we’ll price a matching replacment wall or facing so the whole surface looks intentional, not patched.

OEM vs aftermarket: for Unilock, we almost always recommend OEM pieces from the same batch family. Aftermarket equivalents exist for joint sand and setting compounds, but for the face product itself, the color and texture tolerances are tight enough that a close-enough piece looks exactly like what it is: close enough. The exception is edge trim and some dimensional stone, where a quality alternative from a Los Angeles stone yard can match well and save real money. We’ll lay out both options and the price difference in writing.

Signs Your Unilock Kitchen Remodeling Is Failing

• Cracked or spalled paver faces on the backsplash or island facing. Los Angeles hard water and cycling kitchen heat cause micro-cracks that widen fast, especially on darker colors that absorb more heat from a range.
• Grout or joint sand washing out around a sink or prep area. This usually means the original installer used a joint compound not rated for constant moisture, and water’s been working its way behind the surface.
• A shifted or dropped sink reveal. If the Unilock trim around a farmhouse or undermount sink starts pulling away, the substrate underneath has likely swelled or the setting bed was never sloped correctly.
• Chalky white efflorescence blooming across lower rows. That’s mineral salts wicking through the product, common in Los Angeles basements and slab-on-grade kitchens where moisture moves up from the foundation.
• Hollow-sounding panels when tapped. We find this on U-Cara installations where the adhesive pattern wasn’t full-coverage; the panel’s holding but won’t for long, and one good knock from a pot handle finishes it.

Replacement Cost & What’s Included

In Los Angeles, a Unilock kitchen remodel ranges from $16,520 for a focused replacement of failing paver surfaces and trim to $53,100 for a full kitchen reconfiguration including island work, countertop edge replacement, backsplash rebuild, and new setting beds. Where you land depends on square footage, whether we’re matching an existing batch or replacing a full wall, and how much substrate repair the original install left behind.

Every quote includes the parts, setting materials, labor, tear-out and disposal, and permits pulled on eligible work. We write the scope and the allowances down before anything gets ordered, and if a price changes, it changes on a written change order before we touch the job. You’ll never get a bill at the end that doesn’t match what you signed. Our work carries the 90-Day Done Right Promise, and Tom Barrett’s name is on the contract, not a franchise’s letterhead.

What a Unilock Kitchen Remodel Includes in Los Angeles

• Full Unilock kitchen remodel: $16,520-$53,100
• Countertop installation (edge and trim replacement): $2,360-$7,670
• Backsplash installation (paver or panel): $945-$2,950
• Kitchen island installation or refacing: $3,540-$11,800

DIY or Call Us?

You can safely check what’s failing: look for cracked faces, run your hand along sink trim to feel for movement, and tap panels to hear hollow spots. That tells you what to describe when you call, and a good photo helps. But pulling Unilock pavers or panels and resetting them is not a weekend job if you want the surface flat, the joints tight, and the batch matched. We’ve fixed enough DIY attempts where the homeowner used the wrong joint compound or mixed setting material in a Home Depot bucket without a full bed, and the whole thing failed again in six months.

If the failure is cosmetic and you can live with it, fine. If water’s getting behind the surface, call us at (877) 610-1318 before the substrate rots and a $2,000 fix becomes a $12,000 tear-out.

FAQs